Skip to Content
  1. Home
  2. REVIT Detail Drawings

REVIT Detail Drawings

For the designers, architects, contractors, technologists, draftspersons and engineers, knowing what a manufacturer wants to see for details as they relate to their general requirements can be a challenge. At IKO we want to make your job easier by providing our standard details for the REVIT software at the click of a button. Below are our standard details in .rvt format to be integrated into your construction documents. Please contact your local IKO sales representative for any questions.

IKO-Sheet – BUR-1A – BUR FLASHING DETAIL- ROOF EDGE WITH RAISED PERIMETER EDGE AND METAL FLASHING
IKO-Sheet – BUR-2A – BUR FLASHING DETAIL- SCUPPER THROUGH ROOF EDGE
IKO-Sheet – BUR-3A – BUR FLASHING DETAIL- ROOF EDGE WITH EMBEDDED GRAVEL STOP-DRIP METAL EDGE
IKO-Sheet – BUR-4A – BUR FLASHING DETAIL- BASE FLASHING FOR NON-WALL SUPPORTED DECK
IKO-Sheet – BUR-5A – BUR FLASHING DETAIL- BASE FLASHING FOR WALL-SUPPORTED DECK
IKO-Sheet – BUR-6A – BUR FLASHING DETAIL- SURFACE MOUNTED COUNTERFLASHING FOR CONCRETE WALLS
IKO-Sheet – BUR-7A – BUR FLASHING DETAIL- METAL PARAPET COPING AND BASE FLASHING
IKO-Sheet – BUR-8A – BUR FLASHING DETAIL- EXPANSION JOINT WITH METAL COVER
IKO-Sheet – BUR-9A – BUR FLASHING DETAIL- EXPANSION JOINT WITH PREMANUFACTURED COVER
IKO-Sheet – BUR-10A – BUR FLASHING DETAIL- AREA DIVIDER IN ROOF SYSTEM
IKO-Sheet – BUR-11A – BUR FLASHING DETAIL- EQUIPMENT SUPPORT CURB
IKO-Sheet – BUR-12A – BUR FLASHING DETAIL- EQUIPMENT SUPPORT STAND AND TYPICAL RAIN COLLAR PENETRATION
IKO-Sheet – BUR-13A – BUR FLASHING DETAIL- RAISED CURB DETAIL FOR ROOFTOP AIR HANDLING UNITS AND DUCTS
IKO-Sheet – BUR-14A – BUR FLASHING DETAIL- ISOLATED STACK FLASHING
IKO-Sheet – BUR-15A – BUR FLASHING DETAIL- STRUCTURAL MEMBER THROUGH ROOF DECK
IKO-Sheet – BUR-16A – BUR FLASHING DETAIL- PLUMBING VENT
IKO-Sheet – BUR-17A – BUR FLASHING DETAIL- PENETRATION POCKET
IKO-Sheet – BUR-18A – BUR FLASHING DETAIL- ROOF DRAIN
IKO-Sheet – BUR-19A – BUR FLASHING DETAIL- GUTTER
IKO-Sheet – BUR-20A – BUR FLASHING DETAIL- TERMINATION BAR
IKO-Sheet – MB-1A – MODIFIED BITUMEN FLASHING DETAIL- ANGLED CUT END LAP
IKO-Sheet – MB-2A – MODIFIED BITUMEN FLASHING DETAIL- STAGGERED END END LAP
IKO-Sheet – MB-3A – MODIFIED BITUMEN FLASHING DETAIL- ROOF EDGE WITH BASE FLASHING AND CAP SHEET FLASHING
IKO-Sheet – MB-4A – VENT PIPE FLASHING
IKO-Sheet – MB-5A – SUPPORT COLUMN FLASHING
IKO-Sheet – MB-6A – MODIFIED BITUMEN FLASHING DETAIL- PARAPET-CURB FLASHING ON ALL SUBSTRATES
IKO-Sheet – MB-7A – MODIFIED BITUMEN FLASHING DETAIL- SHINGLE ROOF TIE-IN
IKO-Sheet – MB-8A – MODIFIED BITUMEN FLASHING DETAILS- REGLET MOUNTED COUNTERFLASHING
IKO-Sheet – MB-9A – MODIFIED BITUMEN FLASHING DETAIL- SURFACE MOUNTED COUNTERFLASHING
IKO-Sheet – MB-10A – MODIFIED BITUMEN FLASHING DETAIL- MASONRY COPING
IKO-Sheet – MB-11A – MODIFIED BITUMEN FLASHING DETAIL- METAL COPING (24- MAX- PARAPET HEIGHT)
IKO-Sheet – MB-12A – MODIFIED BITUMEN FLASHING DETAIL- THROUGH WALL SCUPPER
IKO-Sheet – MB-13A – MODIFIED BITUMEN FLASHING DETAIL- DOWNSPOUT SCUPPER BOX
IKO-Sheet – MB-14A – MODIFIED BITUMEN FLASHING DETAIL- CAST IRON ROOF DRAIN
IKO-Sheet – MB-15A – MODIFIED BITUMEN FLASHING DETAIL- RAISED EXPANSION JOINT
IKO-Sheet – MB-16A – MODIFIED BITUMEN FLASHING DETAIL- ROOF LEVEL EXPANSION JOINT
IKO-Sheet – MB-17A – MODIFIED BITUMEN FLASHING DETAIL- WALL EXPANSION JOINT- AUTOCAD SECTION
IKO-Sheet – MB-18A – MODIFIED BITUMEN FLASHING DETAIL- HVAC UNIT
IKO-Sheet – MB-19A – MODIFIED BITUMEN FLASHING DETAIL- BUILT-UP ROOF TIE-IN NEW ROOF AT SAME LEVEL
IKO-Sheet – MB-20A – MODIFIED BITUMEN FLASHING DETAIL- BUILT-UP ROOF TIE-IN WITH TAPERED EDGE
IKO-Sheet – MB-21A – MODIFIED BITUMEN FLASHING DETAIL- NEW PITCH PAN WITH SINGLE SECTION FLASHING
IKO-Sheet – MB-22A – MODIFED BITUMEN FLASHING DETAIL- SUPPORT SLEEPER
IKO-Sheet – MB-23A – MODIFIED BITUMEN FLASHING DETAIL- OUTSIDE CORNER
IKO-Sheet – MB-24A – MODIFIED BITUMEN FLASHING DETAIL- INSIDE CORNER WITHOUT CANT STRIP
IKO-Sheet – MB-25AA – ARMOURBOND FLASHING
IKO-Sheet – MB-25BA – ARMOURBOND FLASHING
IKO-Sheet – MB-26AA – ARMOURBOND FLASHING
IKO-Sheet – MB-26BA – AMOURBOND FLASHING
IKO-Sheet – MB-27A – MODIFIED BITUMEN FLASHING DETAIL- TERMINATION BAR
IKO-Sheet – MB-28A – MODIFIED BITUMEN FLASHING DETAIL- BASE SHEET PERIMETER ATTACHMENT HORIZONTAL
IKO-Sheet – MB-29A – MODIFIED BITUMEN FLASHING DETAIL- BASE SHEET PERIMETER ATTACHMENT VERTICAL

Note: The standard roofing details are provided as a courtesy for consideration by the design professional, and not as a substitute for professional engineering or other licensed professional design and documentation required for the project. Roof should be designed and constructed in accordance with local building code and project specifications. By providing these details for consideration, IKO does not assume any liability for the adequacy of the details provided.

CSA Wind Uplift Tool